Checkout
Thermo-Tec is the original inventor of high performance exhaust insulating and heat control products. From street to strip, they are continually raising the bar to provide the highest quality products at reasonable prices.
|
|
|---|
THE 11001 - Header Wrap White
Natural, 1 in. Wide x 50 ft. Price: $24.95
|
|
THE 11002 - Header Wrap White
Natural, 2 in. Wide x 50 ft. Price: $42.95
|
THE 11021 - Header Wrap Black
Black, 1 in. Wide x 50 ft. Price: $27.95
|
|
THE 11022 - Header Wrap Black
Black, 2 in. Wide x 50 ft. Price: $44.95
|
THE 11248 - Header Exhaust Jacket 8 Cylinder
The quick-wrap high-velocity Exhaust Jacket is an innovative way to insulate and block radiant heat. The jacket cover the tubes vertically allowing for a consistent fit. The fit allows the exhaust system to expand as it comes up to operating temperatures without restrictions and provides air space for added insulation. The material is 8 inches wide and either 12 or 16 feet in length. The Jacket can withstand continuous temperatures up to 2000º F. Price: $89.95
|
This unique spark plug and ignition wire protector comes in four sporty colors; red, blue, black and natural. These dual-purpose sleeves enhance performance, reduce misfires, extend plug wire life and will not react with petroleum products. The double-wall construction keeps the wire and boot cooler in a high-temperature engine. Its universal size fits most boots, is easy to install and - most important - is non-flammable. Cool-It Plug Wire Sleeves can be used in any high-temperature environment from street vehicles to motor homes. Sleeves are available in packs of 4 and 6. The Sleeves can withstand 750° F of conductive heat. The material is non-flammable and fits virtually all plug boots. |
|---|
|
THE 14250 - Spark Plug Wire Heat Shield
4 pc. 6" x 2x2-1/2" The Spark Plug Wire Heat Shield offers the ultimate protection for spark plug wires and boots from conductive and radiant heat, which is a problem. The dual-purpose sleeve has a surface that reflects over 90% of radiant heat up to 2000°, while the inside silica-based fabric prevents conductive heat from penetrating. Price: $30.95
|
|
Price: $29.95
|
|
Price: $29.95
|
Thermo-Flex Aluminum is a composite heat shield material with unlimited uses. The material is manufactured with a combination of materials to provide abrasion-resistance, thermal insulation, and physical containment of hoses and wiring. The combination of aluminum, silica, and stainless steel is combined to produce a sleeving that is flexible, lightweight, and strong. The aluminum-silica combination can be slit for applications such as wire looms or hose covering without disconnecting the ends of the wire or hoses. Thermo-Flex Aluminum can withstand extreme temperatures of up to 750°F and is available in four different colors. |
|---|
|
Price: $12.95
|
|
Price: $13.95
|
|
Price: $15.95
|
|
Price: $13.95
|
|
Price: $15.95
|
|
Price: $17.95
|
|
Price: $15.95
|
|
Price: $18.95
|
|
Price: $20.95
|
Use the Cool-It Mat to battle excessive heat and noise that penetrate the driver compartment through the firewalls and floorboards. It is also perfect in doors, under hoods, and above transmission housings. The Cool-It Mat is composed of resin-bonded silica blanketing insulation sandwiched between a mylar facing on one side and a foil facing on the other. The highly-reflective mylar reflects heat away from surfaces, while the foil side is orientated away from the heat source to conduct any penetrating heat across its surface thus providing the ultimate in heat protection. The silica blanketing is a duel-density composite and is the main sound insulator. It is easy to trim and can be applied with the push-in fasteners provided or any weather strip adhesive. |
|---|
|
Price: $30.95
|
Heavy-Duty Spray Adhesive is a fast-drying, quick-bonding, high temperature contact adhesive. Use it wherever you need a secure, long-lasting, easy-to-apply bond. It is available in a generous 16.75 oz. can. |
|---|
|
THE 12005 - Spray Adhesive
Heavy-Duty, 16 oz. Spray Can Price: $12.95
|
|
|
|---|
THE 11600 - Clamp on Heat Shield Kit 6" x 12"
The flexible clamp on pipe heat shield blocks over 95% of the damaging radiant heat of the exhaust. The High-tech composite construction of the heat shield provides the ultimate in protection. The kits come complete with all clamps and new stainless stand offs. Installs in minutes.. Keep the radiant heat from an exhaust, from going in a certain direction Price: $20.95
|
|
THE 11620 - Clamp on Heat Shield Kit 6" X 24"
Silver, 6 in. Wide x 24 in. Price: $31.95
|
THE 13200 - Battery Wrap Heat Barrier
Battery Wrap, Silver, 8 in. x 40 in., Self-Adhesive Price: $22.95
|
THE 14130 - Thermo Guard FR 24"X48"
Thermo-Guard FR offers the best in head and sound insulation. This lightweight, durable shield does everything: reduces sound, absorbs vibration, protects from radiant heat and provides an extra layer of insulating padding. The product features 100% synthetic fiber felt that provides sound and comfort control and a high-tech foil heat barrier that blocks more than 90% of radiant heat up to 1500 degrees F. Thermo-Guard FR is very easy to apply - it can be trimmed to fit anywhere. Great for use in trucks, RVs, buses, cars, aircraft and homes. Price: $13.95
|
THE 14500 - Cool-Air Tube Heat Shield
Keep your induction air cool with this unique lace up tube cover. The design of the cover allows it to fit from 2-1/2 inch to 3-1/2 inch air tubes up to 36 inches long. The lace on heat shield blocks over 98% of the radiant heat of the turbo and exhaust. The kit comes complete with four different color laces, blue, yellow, red and white. Price: $44.95
|
THE 15001 - Turbo Insulating Kit 4 Cylinder
The Turbo Kit was designed to protect, improve performance, and eliminate turbo lag of a turbo charger. The key to turbo performance is to keep a flow of high temperature exhaust gases moving through the exhaust side impeller. This complete kit, to contain the heat produced by a turbo, fits a wide variety of turbines. The custom cut-to-fit kit comes with an excessive amount of material to cover turbos from the smallest automotive application to heavy-duty truck applications. Kit contains a roll of Exhaust Insulating Wrap 1 or 2 inch, 1 yard of Aluminized Heat Barrier, and a 3' X 6" piece of Exhaust Insulating Wrap. Hardware and instructions are included. Price: $89.95
|
THE 16500 - Muffler/Cat Heat Shield 24"X40"
The Muffler/Catalytic Converter Heat Shield is made up of woven silica with a flexible mylar finish. It can be installed between the catalytic converter, muffler, or any other component to reflect radiant heat away from the undercarriage of the car.The kit includes all necessary fasteners. The mylar material is easily cleaned with soap and water to retain its reflective quality and attractive appearance. The fabric side is attached to the undercarriage and can handle temperatures up to 1200 degree F. The mylar foil side is pointed toward the heat source and can withstand radiant heat temperatures up to 2000 degree F. Price: $55.95
|
In today's high-heat environment, starters take in a lot of damaging heat that destroys the windings of the starter and solenoid. To combat this problem, Thermo-Tec created a non-conductive strap-on heat shield with a highly-reflective mylar surface. The Starter Heat Shield will reflect over 90% of radiant heat up to 2000° F, adding life to the starter and assuring reliable starts. No more of those frustrating temporary starter failures. The Starter Heat Shield is a universal kit that fits all starters. |
|---|
|
Price: $24.95
|
The lamination of a high-temperature fabric to a highly-reflective foil is the makeup of Thermo-Sleeve, which provides protection from radiant heat for hoses and wires. Thermo-Sleeve's ultra light-weight construction provides more insulating than traditional bulky rubber-coated fiberglass. The aluminized sleeving reflects over 90% of radiant heat, and is fireproof and oil resistant. The Thermo-Sleeve can handle conductive heat temperatures of 750°: F and radiant heat temperatures up to 2000° F. |
|---|
|
THE 14005 - 3 ft. Thermo Sleeve Fits 1/4" to 1/2" OD Hose
Fits 1/4 in. to 1/2 in. Hoses/Wires, 3 ft. Length Price: $11.95
|
|
THE 14010 - 3 ft. Thermo Sleeve Fits 5/8" to 1" OD Hose
Fits 5/8 in. to 1 in. Hoses/Wires, 3 ft. Length Price: $14.95
|
|
THE 14015 - 3 ft. Thermo Sleeve Fits 1 1/8"-1 1/2"
Fits 1 1/8 in. to 1 1/2 in. Hoses/Wires, 3 ft. Length Price: $18.95
|
|
THE 14035 - 3 ft. ExpressThermo Sleeve Fits 1 1/2" Velcro
Fits 1 1/2 in. Hoses/Wires, 3 ft. Length Price: $24.95
|
Thermo-Shield protects hoses and wires from radiant heat. Thermo-Shield is used in applications where it is difficult or not practical to disconnect one end of the hose or wire. NOT FOR USE ON EXHAUST. The adhesive-backed composite construction tape can easily be wrapped around the hose or wire to make a clean, professional appearance and protect parts from over 90% of radiant heat up to 2000 degrees farenheight. |
|---|
|
THE 14000 - Thermo-Shield 1 1/2" X 15' Ultra
Ultra, 1.5 in. x 15 ft., Self-Adhesive Roll 2 times as thick Price: $16.50
|
|
THE 14002 - Glue On Thermo-Shield
Ultra, 1.5 in. x 15 ft., Self-Adhesive Price: $14.95
|
The Adhesive Backed Heat Barrier protects parts and components from radiant heat. It can be used in applications to protect painted surfaces, plastic parts or any component from the damaging effects of radiant heat. Aluminized Heat Barrier is made up of woven silica with a flexible aluminized finish. The highly reflective surface of the material is capable of withstanding radiant temperatures in excess of 2000 degree F. The adhesive backed composite construction material can easily be applied to any surface or wrapped around a hose or wire to make a clean professional appearance. Some Typical uses include: Firewall, hoods, hoses, doors and anywhere you want to control radiant heat. |
|---|
|
THE 13500 - Adhesive Backed Heat Barrier 12" X 12"
12 in. x 12 in., Universal Price: $10.95
|
|
THE 13575 - Adhesive Backed Heat Barrier 12" X 24"
24 in. x 12 in., Universal Price: $17.95
|
To finish off a clean and well-protected Exhaust Insulating Wrap application it is recommended to use the Hi-Heat Coating. The coating will protect the wrap from abrasion and harmful liquid spills. Extra resins and binders toughen the surface, extend the life of wrap by protecting it from friction, and seal the pores to minimize the penetration of harmful liquids. The coating also works excellent as a paint directy on metal surfaces. |
|---|
|
THE 12001 - High Heat Coating
Black, 11 oz. Spray Can Price: $8.95
|
|
THE 12002 - Aluminum High Heat Coating
Silver, 11 oz. Spray Can Price: $8.95
|
|
|
|---|
|
THE 13101 - V-8 Snap Strap Kit 8 - 9" Straps 4 - 18" Straps
Stainless Steel Fasteners, Eight 9 in. Straps, Four 18 in. Straps, V8 Kit Price: $26.95
|
|
THE 13150 - Universal 9" Snap Strap Kit 12 - 9" Straps
Stainless Steel Fasteners, 9 in. Straps, Set of 12 Price: $24.95
|
Click the  to add an item to your shopping Cart( you can always remove it later) |
Prices, specifications, and images are subject to change without notice. Some images are only a representation and might not be the actual product. 
Not responsible for typographical errors. Manufacturer rebates, terms, conditions, and expiration dates are subject to manufacturers printed forms. |